diff --git a/extlinux.conf b/extlinux.conf deleted file mode 100644 index b06ccc7..0000000 --- a/extlinux.conf +++ /dev/null @@ -1,22 +0,0 @@ -# File generated by DrakX/drakboot -default Mageia -timeout 20 -menu title Boot Menu - -label Mageia - kernel /boot/vmlinuz - initrd /boot/initrd - fdtdir /usr/lib/linux-4.19.11-desktop-2.mga7 - append root=UUID=f9fdc05d-2cc9-42d8-a8dc-2f79ff008045 dwc_otg.lpm_enable=0 kgdboc=ttyS0,115200 console=tty1 rootwait fsck.repair=1 elevator=deadline cma=256M\@512M audit=0 disable_overscan=1 - -label linux - kernel /boot/vmlinuz - initrd /boot/initrd.img - fdtdir /usr/lib/linux-4.19.12-desktop-2.mga7 - append root=UUID=f9fdc05d-2cc9-42d8-a8dc-2f79ff008045 8250.nr_uarts=1 console=ttyS0,115200 console=tty1 elevator=deadline cma=256M@512M - -label desktop 4.19.12-2.mga7 - kernel /boot/vmlinuz-4.19.12-desktop-2.mga7 - initrd /boot/initrd-4.19.12-desktop-2.mga7.img - fdtdir /usr/lib/linux-4.19.12-desktop-2.mga7 - append root=UUID=f9fdc05d-2cc9-42d8-a8dc-2f79ff008045 8250.nr_uarts=1 console=ttyS0,115200 console=tty1 elevator=deadline cma=256M@512M diff --git a/rpi/bcm2836-rpi-2-b.dtb b/rpi/bcm2836-rpi-2-b.dtb deleted file mode 100755 index 06ba65b..0000000 Binary files a/rpi/bcm2836-rpi-2-b.dtb and /dev/null differ diff --git a/rpi/bcm2837-rpi-3-b-plus.dtb b/rpi/bcm2837-rpi-3-b-plus.dtb deleted file mode 100755 index 9fa2dd4..0000000 Binary files a/rpi/bcm2837-rpi-3-b-plus.dtb and /dev/null differ diff --git a/rpi/bcm2837-rpi-3-b.dtb b/rpi/bcm2837-rpi-3-b.dtb deleted file mode 100755 index 7ed21fb..0000000 Binary files a/rpi/bcm2837-rpi-3-b.dtb and /dev/null differ diff --git a/rpi/boot.cmd b/rpi/boot.cmd deleted file mode 100644 index f16ad1d..0000000 --- a/rpi/boot.cmd +++ /dev/null @@ -1,5 +0,0 @@ -fatload mmc 0:1 ${kernel_addr_r} vmlinuz -fatload mmc 0:1 ${fdt_addr_r} bcm2710-rpi-3-b.dtb -fatload mmc 0:1 ${ramdisk_addr_r} initrd.img -setenv bootargs console=ttyAMA0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait panic=10 -bootz ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r} diff --git a/rpi/config.txt b/rpi/config.txt deleted file mode 100644 index a27b5de..0000000 --- a/rpi/config.txt +++ /dev/null @@ -1,1193 +0,0 @@ -################################################################################ -## Raspberry Pi Configuration Settings -## -## Revision 16, 2013/06/22 -## -## Details taken from the eLinux wiki -## For up-to-date information please refer to wiki page. -## -## Wiki Location : http://elinux.org/RPiconfig -## -## -## Description: -## Details of each setting are described with each section that begins with -## a double hashed comment ('##') -## It is up to the user to remove the single hashed comment ('#') from each -## option they want to enable, and to set the specific value of that option. -## -## Overclock settings will be disabled at runtime if the SoC reaches temp_limit -## -################################################################################ - -#dtoverlay=vc4-kms-v3d,cma-128 - - - - - -################################################################################ -## Standard Definition Video Settings -################################################################################ - -## sdtv_mode -## defines the TV standard for composite output -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Normal NTSC (Default) -## 1 Japanese version of NTSC - no pedestal -## 2 Normal PAL -## 3 Brazilian version of PAL - 525/60 rather than 625/50, different -## subcarrier -## -#sdtv_mode=0 - -## sdtv_aspect -## defines the aspect ratio for composite output -## -## Value Description -## ------------------------------------------------------------------------- -## 1 4:3 (Default) -## 2 14:9 -## 3 16:9 -## -sdtv_aspect=3 - -## sdtv_disable_colourburst -## Disables colour burst on composite output. The picture will be -## monochrome, but possibly sharper -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Colour burst is enabled (Default) -## 1 Colour burst is disabled -## -#sdtv_disable_colourburst=1 - -################################################################################ -## High Definition Video Settings -################################################################################ - -## hdmi_safe -## Use "safe mode" settings to try to boot with maximum hdmi compatibility. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Disabled (Default) -## 1 Enabled (this does: hdmi_force_hotplug=1, -## hdmi_ignore_edid=0xa5000080, -## config_hdmi_boost=4, hdmi_group=2, -## hdmi_mode=4, disable_overscan=0, -## overscan_left=24, overscan_right=24, -## overscan_top=24, overscan_bottom=24) -## -#hdmi_safe=1 - -## hdmi_force_hotplug -## Pretends HDMI hotplug signal is asserted so it appears a HDMI display -## is attached -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Disabled (Default) -## 1 Use HDMI mode even if no HDMI monitor is detected -## -#hdmi_force_hotplug=1 - -## hdmi_ignore_hotplug -## Pretends HDMI hotplug signal is not asserted so it appears a HDMI -## display is not attached -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Disabled (Default) -## 1 Use composite mode even if HDMI monitor is detected -## -#hdmi_ignore_hotplug=1 - -## hdmi_drive -## chooses between HDMI and DVI modes -## -## Value Description -## ------------------------------------------------------------------------- -## 1 Normal DVI mode (No sound) -## 2 Normal HDMI mode (Sound will be sent if supported and enabled) -## -#hdmi_drive=2 - -## hdmi_ignore_edid -## Enables the ignoring of EDID/display data -## -#hdmi_ignore_edid=0xa5000080 - -## hdmi_edid_file -## Read the EDID data from the edid.dat file instead of from the attached -## device -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Read EDID data from attached device (Default) -## 1 Read EDID data from edid.txt file -## -#hdmi_edid_file=1 - -## hdmi_ignore_edid_audio -## Pretends all audio formats are unsupported by display. This means ALSA -## will default to analogue. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Use EDID provided values (Default) -## 1 Pretend all audio formats are unsupported -## -#hdmi_ignore_edid_audio=1 - -## hdmi_force_edid_audio -## Pretends all audio formats are supported by display, allowing -## passthrough of DTS/AC3 even when not reported as supported. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Use EDID provided values (Default) -## 1 Pretend all audio formats are supported -## -#hdmi_force_edid_audio=1 - -## hdmi_force_edid_3d -## Pretends all CEA modes support 3D even when edid doesn't indicate -## support for them. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Use EDID provided values (Default) -## 1 Pretend 3D mode is supported -## -#hdmi_force_edid_3d=1 - -## avoid_edid_fuzzy_match -## Avoid fuzzy matching of modes described in edid. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Use fuzzy matching (Default) -## 1 Avoid fuzzy matching -## -#avoid_edid_fuzzy_match=1 - -## hdmi_pixel_encoding -## Force the pixel encoding mode. -## By default it will use the mode requested from edid so shouldn't -## need changing. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Use EDID provided values (Default) -## 1 RGB limited (16-235) -## 2 RGB full ( 0-255) -## 3 YCbCr limited (16-235) -## 4 YCbCr limited ( 0-255) -## -#hdmi_pixel_encoding=1 - -## hdmi_group -## Defines the HDMI type -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Use the preferred group reported by the edid (Default) -## 1 CEA -## 2 DMT -## -#hdmi_group=1 - -## hdmi_mode -## defines screen resolution in CEA or DMT format -## -## H means 16:9 variant (of a normally 4:3 mode). -## 2x means pixel doubled (i.e. higher clock rate, with each pixel repeated -## twice) -## 4x means pixel quadrupled (i.e. higher clock rate, with each pixel -## repeated four times) -## reduced blanking means fewer bytes are used for blanking within the data -## stream (i.e. lower clock rate, with fewer wasted bytes) -## -## Value hdmi_group=CEA hdmi_group=DMT -## ------------------------------------------------------------------------- -## 1 VGA 640x350 85Hz -## 2 480p 60Hz 640x400 85Hz -## 3 480p 60Hz H 720x400 85Hz -## 4 720p 60Hz 640x480 60Hz -## 5 1080i 60Hz 640x480 72Hz -## 6 480i 60Hz 640x480 75Hz -## 7 480i 60Hz H 640x480 85Hz -## 8 240p 60Hz 800x600 56Hz -## 9 240p 60Hz H 800x600 60Hz -## 10 480i 60Hz 4x 800x600 72Hz -## 11 480i 60Hz 4x H 800x600 75Hz -## 12 240p 60Hz 4x 800x600 85Hz -## 13 240p 60Hz 4x H 800x600 120Hz -## 14 480p 60Hz 2x 848x480 60Hz -## 15 480p 60Hz 2x H 1024x768 43Hz DO NOT USE -## 16 1080p 60Hz 1024x768 60Hz -## 17 576p 50Hz 1024x768 70Hz -## 18 576p 50Hz H 1024x768 75Hz -## 19 720p 50Hz 1024x768 85Hz -## 20 1080i 50Hz 1024x768 120Hz -## 21 576i 50Hz 1152x864 75Hz -## 22 576i 50Hz H 1280x768 reduced blanking -## 23 288p 50Hz 1280x768 60Hz -## 24 288p 50Hz H 1280x768 75Hz -## 25 576i 50Hz 4x 1280x768 85Hz -## 26 576i 50Hz 4x H 1280x768 120Hz reduced blanking -## 27 288p 50Hz 4x 1280x800 reduced blanking -## 28 288p 50Hz 4x H 1280x800 60Hz -## 29 576p 50Hz 2x 1280x800 75Hz -## 30 576p 50Hz 2x H 1280x800 85Hz -## 31 1080p 50Hz 1280x800 120Hz reduced blanking -## 32 1080p 24Hz 1280x960 60Hz -## 33 1080p 25Hz 1280x960 85Hz -## 34 1080p 30Hz 1280x960 120Hz reduced blanking -## 35 480p 60Hz 4x 1280x1024 60Hz -## 36 480p 60Hz 4x H 1280x1024 75Hz -## 37 576p 50Hz 4x 1280x1024 85Hz -## 38 576p 50Hz 4x H 1280x1024 120Hz reduced blanking -## 39 1080i 50Hz reduced blanking 1360x768 60Hz -## 40 1080i 100Hz 1360x768 120Hz reduced blanking -## 41 720p 100Hz 1400x1050 reduced blanking -## 42 576p 100Hz 1400x1050 60Hz -## 43 576p 100Hz H 1400x1050 75Hz -## 44 576i 100Hz 1400x1050 85Hz -## 45 576i 100Hz H 1400x1050 120Hz reduced blanking -## 46 1080i 120Hz 1440x900 reduced blanking -## 47 720p 120Hz 1440x900 60Hz -## 48 480p 120Hz 1440x900 75Hz -## 49 480p 120Hz H 1440x900 85Hz -## 50 480i 120Hz 1440x900 120Hz reduced blanking -## 51 480i 120Hz H 1600x1200 60Hz -## 52 576p 200Hz 1600x1200 65Hz -## 53 576p 200Hz H 1600x1200 70Hz -## 54 576i 200Hz 1600x1200 75Hz -## 55 576i 200Hz H 1600x1200 85Hz -## 56 480p 240Hz 1600x1200 120Hz reduced blanking -## 57 480p 240Hz H 1680x1050 reduced blanking -## 58 480i 240Hz 1680x1050 60Hz -## 59 480i 240Hz H 1680x1050 75Hz -## 60 1680x1050 85Hz -## 61 1680x1050 120Hz reduced blanking -## 62 1792x1344 60Hz -## 63 1792x1344 75Hz -## 64 1792x1344 120Hz reduced blanking -## 65 1856x1392 60Hz -## 66 1856x1392 75Hz -## 67 1856x1392 120Hz reduced blanking -## 68 1920x1200 reduced blanking -## 69 1920x1200 60Hz -## 70 1920x1200 75Hz -## 71 1920x1200 85Hz -## 72 1920x1200 120Hz reduced blanking -## 73 1920x1440 60Hz -## 74 1920x1440 75Hz -## 75 1920x1440 120Hz reduced blanking -## 76 2560x1600 reduced blanking -## 77 2560x1600 60Hz -## 78 2560x1600 75Hz -## 79 2560x1600 85Hz -## 80 2560x1600 120Hz reduced blanking -## 81 1366x768 60Hz -## 82 1080p 60Hz -## 83 1600x900 reduced blanking -## 84 2048x1152 reduced blanking -## 85 720p 60Hz -## 86 1366x768 reduced blanking -## -#hdmi_mode=1 - -## config_hdmi_boost -## configure the signal strength of the HDMI interface. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 (Default) -## 1 -## 2 -## 3 -## 4 Try if you have interference issues with HDMI -## 5 -## 6 -## 7 Maximum -## -#config_hdmi_boost=0 - -## hdmi_ignore_cec_init -## Doesn't sent initial active source message. Avoids bringing -## (CEC enabled) TV out of standby and channel switch when rebooting. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Normal behaviour (Default) -## 1 Doesn't sent initial active source message -## -#hdmi_ignore_cec_init=1 - -## hdmi_ignore_cec -## Pretends CEC is not supported at all by TV. -## No CEC functions will be supported. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Normal behaviour (Default) -## 1 Pretend CEC is not supported by TV -## -#hdmi_ignore_cec=1 - -################################################################################ -## Overscan Video Settings -################################################################################ - -## overscan_left -## Number of pixels to skip on left -## -#overscan_left=0 - -## overscan_right -## Number of pixels to skip on right -## -#overscan_right=0 - -## overscan_top -## Number of pixels to skip on top -## -#overscan_top=0 - -## overscan_bottom -## Number of pixels to skip on bottom -## -#overscan_bottom=0 - -## disable_overscan -## Set to 1 to disable overscan -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Overscan Enabled (Default) -## 1 Overscan Disabled -## -#disable_overscan=1 - -################################################################################ -## Framebuffer Video Settings -################################################################################ - -## framebuffer_width -## Console framebuffer width in pixels. Default is display width minus -## overscan. -## -#framebuffer_width=0 - -## framebuffer_height -## Console framebuffer height in pixels. Default is display height minus -## overscan. -## -#framebuffer_height=0 - -## framebuffer_depth -## Console framebuffer depth in bits per pixel. -## -## Value Description -## ------------------------------------------------------------------------- -## 8 Valid, but default RGB palette makes an unreadable screen -## 16 (Default) -## 24 Looks better but has corruption issues as of 2012/06/15 -## 32 Has no corruption issues but needs framebuffer_ignore_alpha=1 -## and shows the wrong colors as of 2012/06/15 -## -#framebuffer_depth=16 - -## framebuffer_ignore_alpha -## Set to 1 to disable alpha channel. Helps with 32bit. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Enable Alpha Channel (Default) -## 1 Disable Alpha Channel -## -#framebuffer_ignore_alpha=0 - -################################################################################ -## General Video Settings -################################################################################ - -## display_rotate -## Rotate the display clockwise or flip the display. -## The 90 and 270 degrees rotation options require additional memory on GPU, -## so won't work with the 16M GPU split. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 0 degrees (Default) -## 1 90 degrees -## 2 180 degrees -## 3 270 degrees -## 0x10000 Horizontal flip -## 0x20000 Vertical flip -## -#display_rotate=0 - -## dispmanx_offline -## Set to "1" to enable offline compositing -## -## Default 0 -## -#dispmanx_offline=0 - -################################################################################ -## Licensed Codecs -## -## Hardware decoding of additional codecs can be enabled by purchasing a -## license that is locked to the CPU serial number of your Raspberry Pi. -## -## Up to 8 licenses per CODEC can be specified as a comma seperated list. -## -################################################################################ - -## decode_MPG2 -## License key to allow hardware MPEG-2 decoding. -## -#decode_MPG2=0x12345678 - -## decode_WVC1 -## License key to allow hardware VC-1 decoding. -## -#decode_WVC1=0x12345678 - -################################################################################ -## Camera Settings -################################################################################ - -## start_x -## Set to "1" to enable the camera module. -## -## Enabling the camera requires gpu_mem option to be specified with a value -## of at least 128. -## -## Default 0 -## -#start_x=0 - -## disable_camera_led -## Turn off the red camera led when recording video or taking a still -## picture. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 LED enabled (Default) -## 1 LED disabled -## -#disable_camera_led=1 - -################################################################################ -## Test Settings -################################################################################ - -## test_mode -## Enable test sound/image during boot for manufacturing test. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Disable Test Mod (Default) -## 1 Enable Test Mode -## -#test_mode=0 - -################################################################################ -## Memory Settings -################################################################################ - -## disable_l2cache -## Disable arm access to GPU's L2 cache. Needs corresponding L2 disabled -## kernel. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Enable L2 Cache (Default) -## 1 Disable L2 cache -## -#disable_l2cache=0 - -## gpu_mem -## GPU memory allocation in MB for all board revisions. -## -## Default 64 -## -gpu_mem=128 - -## gpu_mem_256 -## GPU memory allocation in MB for 256MB board revision. -## This option overrides gpu_mem. -## -#gpu_mem_256=192 - -## gpu_mem_512 -## GPU memory allocation in MB for 512MB board revision. -## This option overrides gpu_mem. -## -#gpu_mem_512=448 - -## gpu_mem_1024 -## GPU memory allocation in MB for 1024MB board revision. -## This option overrides gpu_mem. -## -#gpu_mem_1024=944 - -## disable_pvt -## Disable adjusting the refresh rate of RAM every 500ms -## (measuring RAM temparature). -## -#disable_pvt=1 - -################################################################################ -## CMA - Dynamic Memory Split -## -## CMA enables dynamic management of the ARM and GPU memory split at runtime. -## -## The following options need to be in cmdline.txt for CMA to work: -## coherent_pool=6M smsc95xx.turbo_mode=N -## -################################################################################ - -## cma_lwm -## When GPU has less than cma_lwm (low water mark) memory available it -## will request some from ARM. -## -#cma_lwm=16 - -## cma_hwm -## When GPU has more than cma_hwm (high water mark) memory available it -## will release some to ARM. -## -#cma_hwm=32 - -################################################################################ -## Boot Option Settings -################################################################################ - -## disable_commandline_tags -## Stop start.elf from filling in ATAGS (memory from 0x100) before -## launching kernel -## -#disable_commandline_tags=0 - -## cmdline (string) -## Command line parameters. Can be used instead of cmdline.txt file -## -#cmdline="" - -## kernel (string) -## Alternative name to use when loading kernel. -## -#kernel="" - -## kernel_address -## Address to load kernel.img file at -## -#kernel_address=0x00000000 - -## kernel_old -## Support loading old kernels -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Disabled (Default) -## 1 Load kernel at address 0x00000000 -## -#kernel_old=1 - -## ramfsfile (string) -## ramfs file to load -## -#ramfsfile="" - -## ramfsaddr -## Address to load ramfs file at -## -#ramfsaddr=0x00000000 - -## initramfs (string address) -## ramfs file and address to load it at (it's like ramfsfile+ramfsaddr in -## one option). -## -## NOTE: this option uses different syntax than all other options - you -## should not use "=" character here. -## -#initramfs initramf.gz 0x00800000 - -## device_tree_address -## Address to load device_tree at -## -#device_tree_address=0x00000000 - -## init_uart_baud -## Initial uart baud rate. -## -## Default 115200 -## -#init_uart_baud=115200 - -## init_uart_clock -## Initial uart clock. -## -## Default 3000000 (3MHz) -## -#init_uart_clock=3000000 - -## init_emmc_clock -## Initial emmc clock, increasing this can speedup your SD-card. -## -## Default 100000000 (100mhz) -## -#init_emmc_clock=100000000 - -## boot_delay -## Wait for a given number of seconds in start.elf before loading -## kernel.img. -## -## delay = (1000 * boot_delay) + boot_delay_ms -## -## Default 1 -## -#boot_delay=0 - -## boot_delay_ms -## Wait for a given number of milliseconds in start.elf before loading -## kernel.img. -## -## delay = (1000 * boot_delay) + boot_delay_ms -## -## Default 0 -## -#boot_delay_ms=0 - -## avoid_safe_mode -## Adding a jumper between pins 5 & 6 of P1 enables a recovery Safe Mode. -## If pins 5 & 6 are used for connecting to external devices (e.g. GPIO), -## then this setting can be used to ensure Safe Mode is not triggered. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Respect Safe Mode input (Default) -## 1 Ignore Safe Mode input -## -#avoid_safe_mode=1 - -## disable_splash -## Avoids the rainbow splash screen on boot. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Splash screen enabled (Default) -## 1 Splash screen disabled -## -#disable_splash=1 - -################################################################################ -## Overclocking Settings -## -## ARM, SDRAM and GPU each have their own PLLs and can have unrelated -## frequencies. -## -## The GPU core, h264, v3d and isp share a PLL, so need to have related -## frequencies. -## pll_freq = floor(2400 / (2 * core_freq)) * (2 * core_freq) -## gpu_freq = pll_freq / [even number] -## -## The effective gpu_freq is automatically rounded to nearest even integer, so -## asking for core_freq = 500 and gpu_freq = 300 will result in divisor of -## 2000/300 = 6.666 => 6 and so 333.33MHz. -## -## -## Standard Profiles: -## arm_freq core_freq sdram_freq over_voltage -## ------------------------------------------------------------------------- -## None 700 250 400 0 -## Modest 800 300 400 0 -## Medium 900 333 450 2 -## High 950 450 450 6 -## Turbo 1000 500 500 6 -## -################################################################################ - -## force_turbo -## Control the kernel "ondemand" governor. It has no effect if no overclock -## settings are specified. -## May set warrany bit. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Enable dynamic clocks and voltage for the ARM core, GPU core and -## SDRAM (Default). -## Overclocking of h264_freq, v3d_freq and isp_freq is ignored. -## 1 Disable dynamic clocks and voltage for the ARM core, GPU core -## and SDRAM. -## Overclocking of h264_freq, v3d_freq and isp_freq is allowed. -## -#force_turbo=0 - -## initial_turbo -## Enables turbo mode from boot for the given value in seconds (up to 60) -## or until cpufreq sets a frequency. Can help with sdcard corruption if -## overclocked. -## -## Default 0 -## -#initial_turbo=0 - -## temp_limit -## Overheat protection. Sets clocks and voltages to default when the SoC -## reaches this Celsius value. -## Setting this higher than default voids warranty. -## -## Default 85 -## -#temp_limit=85 - -## arm_freq -## Frequency of ARM in MHz. -## -## Default 700. -## -arm_freq=900 - -## arm_freq_min -## Minimum frequency of ARM in MHz (used for dynamic clocking). -## -## Default 700. -## -#arm_freq_min=700 - -## gpu_freq -## Sets core_freq, h264_freq, isp_freq, v3d_freq together. -## -## Default 250. -## -#gpu_freq=250 - -## core_freq -## Frequency of GPU processor core in MHz. It has an impact on ARM -## performance since it drives L2 cache. -## -## Default 250. -## -#core_freq=250 - -## core_freq_min -## Minimum frequency of GPU processor core in MHz (used for dynamic -## clocking). It has an impact on ARM performance since it drives L2 cache. -## -## Default 250. -## -#core_freq_min=250 - -## h264_freq -## Frequency of hardware video block in MHz. -## -## Default 250. -## -#h264_freq=250 - -## isp_freq -## Frequency of image sensor pipeline block in MHz. -## -## Default 250. -## -#isp_freq=250 - -## v3d_freq -## Frequency of 3D block in MHz. -## -## Default 250. -## -#v3d_freq=250 - -## sdram_freq -## Frequency of SDRAM in MHz. -## -## Default 400. -## -#sdram_freq=400 - -## sdram_freq_min -## Minimum frequency of SDRAM in MHz (used for dynamic clocking). -## -## Default 400. -## -#sdram_freq_min=400 - -## avoid_pwm_pll -## Don't dedicate a pll to PWM audio. This will reduce analogue audio -## quality slightly. The spare PLL allows the core_freq to be set -## independently from the rest of the gpu allowing more control over -## overclocking. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Linked core_freq (Default) -## 1 Unlinked core_freq -## -#avoid_pwm_pll=1 - -################################################################################ -## Voltage Settings -################################################################################ - -## current_limit_override -## Disables SMPS current limit protection. Can help if you are currently -## hitting a reboot failure when overclocking too high. -## May set warrany bit. -## -#current_limit_override=0x5A000020 - -## over_voltage -## ARM/GPU core voltage adjust. -## May set warrany bit. -## -## Value Description -## ------------------------------------------------------------------------- -## -16 0.8 V -## -15 0.825 V -## -14 0.85 V -## -13 0.875 V -## -12 0.9 V -## -11 0.925 V -## -10 0.95 V -## -9 0.975 V -## -8 1.0 V -## -7 1.025 V -## -6 1.05 V -## -5 1.075 V -## -4 1.1 V -## -3 1.125 V -## -2 1.15 V -## -1 1.175 V -## 0 1.2 V (Default) -## 1 1.225 V -## 2 1.25 V -## 3 1.275 V -## 4 1.3 V -## 5 1.325 V -## 6 1.35 V -## 7 1.375 V (requires force_turbo=1 or current_limit_override) -## 8 1.4 V (requires force_turbo=1 or current_limit_override) -## -#over_voltage=0 - -## over_voltage_min -## Minimum ARM/GPU core voltage adjust (used for dynamic clocking). -## -## Value Description -## ------------------------------------------------------------------------- -## -16 0.8 V -## -15 0.825 V -## -14 0.85 V -## -13 0.875 V -## -12 0.9 V -## -11 0.925 V -## -10 0.95 V -## -9 0.975 V -## -8 1.0 V -## -7 1.025 V -## -6 1.05 V -## -5 1.075 V -## -4 1.1 V -## -3 1.125 V -## -2 1.15 V -## -1 1.175 V -## 0 1.2 V (Default) -## 1 1.225 V -## 2 1.25 V -## 3 1.275 V -## 4 1.3 V -## 5 1.325 V -## 6 1.35 V -## 7 1.375 V (requires force_turbo=1) -## 8 1.4 V (requires force_turbo=1) -## -#over_voltage_min=0 - -## over_voltage_sdram -## Sets over_voltage_sdram_c, over_voltage_sdram_i, over_voltage_sdram_p -## together -## -## Value Description -## ------------------------------------------------------------------------- -## -16 0.8 V -## -15 0.825 V -## -14 0.85 V -## -13 0.875 V -## -12 0.9 V -## -11 0.925 V -## -10 0.95 V -## -9 0.975 V -## -8 1.0 V -## -7 1.025 V -## -6 1.05 V -## -5 1.075 V -## -4 1.1 V -## -3 1.125 V -## -2 1.15 V -## -1 1.175 V -## 0 1.2 V (Default) -## 1 1.225 V -## 2 1.25 V -## 3 1.275 V -## 4 1.3 V -## 5 1.325 V -## 6 1.35 V -## 7 1.375 V -## 8 1.4 V -## -#over_voltage_sdram=0 - -## over_voltage_sdram_c -## SDRAM controller voltage adjust. -## -## Value Description -## ------------------------------------------------------------------------- -## -16 0.8 V -## -15 0.825 V -## -14 0.85 V -## -13 0.875 V -## -12 0.9 V -## -11 0.925 V -## -10 0.95 V -## -9 0.975 V -## -8 1.0 V -## -7 1.025 V -## -6 1.05 V -## -5 1.075 V -## -4 1.1 V -## -3 1.125 V -## -2 1.15 V -## -1 1.175 V -## 0 1.2 V (Default) -## 1 1.225 V -## 2 1.25 V -## 3 1.275 V -## 4 1.3 V -## 5 1.325 V -## 6 1.35 V -## 7 1.375 V -## 8 1.4 V -## -#over_voltage_sdram_c=0 - -## over_voltage_sdram_i -## SDRAM I/O voltage adjust. -## -## Value Description -## ------------------------------------------------------------------------- -## -16 0.8 V -## -15 0.825 V -## -14 0.85 V -## -13 0.875 V -## -12 0.9 V -## -11 0.925 V -## -10 0.95 V -## -9 0.975 V -## -8 1.0 V -## -7 1.025 V -## -6 1.05 V -## -5 1.075 V -## -4 1.1 V -## -3 1.125 V -## -2 1.15 V -## -1 1.175 V -## 0 1.2 V (Default) -## 1 1.225 V -## 2 1.25 V -## 3 1.275 V -## 4 1.3 V -## 5 1.325 V -## 6 1.35 V -## 7 1.375 V -## 8 1.4 V -## -#over_voltage_sdram_i=0 - -## over_voltage_sdram_p -## SDRAM phy voltage adjust. -## -## Value Description -## ------------------------------------------------------------------------- -## -16 0.8 V -## -15 0.825 V -## -14 0.85 V -## -13 0.875 V -## -12 0.9 V -## -11 0.925 V -## -10 0.95 V -## -9 0.975 V -## -8 1.0 V -## -7 1.025 V -## -6 1.05 V -## -5 1.075 V -## -4 1.1 V -## -3 1.125 V -## -2 1.15 V -## -1 1.175 V -## 0 1.2 V (Default) -## 1 1.225 V -## 2 1.25 V -## 3 1.275 V -## 4 1.3 V -## 5 1.325 V -## 6 1.35 V -## 7 1.375 V -## 8 1.4 V -## -#over_voltage_sdram_p=0 - -################################################################################ -## USB Power -################################################################################ - -## max_usb_current -## When set to 1, change the output current limit (for all 4 USB -## ports combined) from 600mA to double that, 1200mA. -## -## This option is not available for Model A/B boards. -## -## Default 0. -## -#max_usb_current=0 - -################################################################################ -## Base Device Tree Parameters -################################################################################ - -## audio -## Enable the onboard ALSA audio -## -## Default off. -## -dtparam=audio=on - -## i2c_arm -## Enable the ARM's i2c interface -## -## Default off. -## -#dtparam=i2c_arm=off - -## i2c_vc -## Enable the i2c interface -## -## Usually reserved for the VideoCore processor -## -## Default off. -## -#dtparam=i2c_vc=off - -## i2c_arm_baudrate -## Set the baudrate of the ARM's i2c interface -## -## Default 100000. -## -#dtparam=i2c_arm_baudrate=100000 - -## i2c_vc_baudrate -## Set the baudrate of the VideoCore i2c interface -## -## Default 100000. -## -#dtparam=i2c_vc_baudrate=100000 - -## i2s -## Set to "on" to enable the i2s interface -## -## Default off. -## -#dtparam=i2s=off - -## spi -## Set to "on" to enable the spi interfaces -## -## Default off. -## -#dtparam=spi=off - -## random -## Set to "on" to enable the hardware random -## -## Default off. -## -#dtparam=random=off - -## uart0 -## Set to "off" to disable uart0 -## -## Default on. -## -#dtparam=uart0=on - -## watchdog -## Set to "on" to enable the hardware watchdog -## -## Default off. -## -#dtparam=watchdog=off - -## act_led_trigger -## Choose which activity the LED tracks. -## -## Use "heartbeat" for a nice load indicator. -## -## Default mmc. -## -#dtparam=act_led_trigger=mmc - -## act_led_activelow -## Set to "on" to invert the sense of the LED -## -## Default off. -## -#dtparam=act_led_activelow=off - -## act_led_gpio -## Set which GPIO to use for the activity LED -## -## In case you want to connect it to an external device -## -## Default 16 on a non-Plus board, 47 on a Plus or Pi 2. -## -#dtparam=act_led_gpio=47 - -## pwr_led_trigger -## Choose which activity the LED tracks. -## -## Use "heartbeat" for a nice load indicator. -## -## Not available on Model A/B boards. -## -## Default mmc. -## -#dtparam=pwr_led_trigger=mmc - -## pwr_led_activelow -## Set to "on" to invert the sense of the LED -## -## Not available on Model A/B boards. -## -## Default off. -## -#dtparam=pwr_led_activelow=off - -## pwr_led_gpio -## Set which GPIO to use for the PWR LED -## -## In case you want to connect it to an external device -## -## Not available on Model A/B boards. -## -## Default 35. -## -#dtparam=pwr_led_gpio=35 diff --git a/rpi2/10-monitor.conf b/rpi2/10-monitor.conf deleted file mode 100644 index 6b319d7..0000000 --- a/rpi2/10-monitor.conf +++ /dev/null @@ -1,3 +0,0 @@ -Section "Extensions" - Option "DPMS" "Disable" -EndSection diff --git a/rpi2/bcm2836-rpi-2-b.dtb b/rpi2/bcm2836-rpi-2-b.dtb deleted file mode 100755 index 06ba65b..0000000 Binary files a/rpi2/bcm2836-rpi-2-b.dtb and /dev/null differ diff --git a/rpi2/bcm2837-rpi-3-b-plus.dtb b/rpi2/bcm2837-rpi-3-b-plus.dtb deleted file mode 100755 index 9fa2dd4..0000000 Binary files a/rpi2/bcm2837-rpi-3-b-plus.dtb and /dev/null differ diff --git a/rpi2/bcm2837-rpi-3-b.dtb b/rpi2/bcm2837-rpi-3-b.dtb deleted file mode 100755 index 7ed21fb..0000000 Binary files a/rpi2/bcm2837-rpi-3-b.dtb and /dev/null differ diff --git a/rpi2/boot.cmd b/rpi2/boot.cmd deleted file mode 100644 index cf2b8ea..0000000 --- a/rpi2/boot.cmd +++ /dev/null @@ -1,5 +0,0 @@ -fatload mmc 0:1 ${kernel_addr_r} vmlinuz -fatload mmc 0:1 ${fdt_addr} bcm2837-rpi-3-b.dtb -fatload mmc 0:1 ${ramdisk_addr_r} initrd.img -setenv bootargs console=ttyAMA0,115200 earlyprintk root=/dev/mmcblk0p2 rootwait panic=10 -bootz ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr} diff --git a/rpi2/config.txt b/rpi2/config.txt deleted file mode 100644 index a27b5de..0000000 --- a/rpi2/config.txt +++ /dev/null @@ -1,1193 +0,0 @@ -################################################################################ -## Raspberry Pi Configuration Settings -## -## Revision 16, 2013/06/22 -## -## Details taken from the eLinux wiki -## For up-to-date information please refer to wiki page. -## -## Wiki Location : http://elinux.org/RPiconfig -## -## -## Description: -## Details of each setting are described with each section that begins with -## a double hashed comment ('##') -## It is up to the user to remove the single hashed comment ('#') from each -## option they want to enable, and to set the specific value of that option. -## -## Overclock settings will be disabled at runtime if the SoC reaches temp_limit -## -################################################################################ - -#dtoverlay=vc4-kms-v3d,cma-128 - - - - - -################################################################################ -## Standard Definition Video Settings -################################################################################ - -## sdtv_mode -## defines the TV standard for composite output -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Normal NTSC (Default) -## 1 Japanese version of NTSC - no pedestal -## 2 Normal PAL -## 3 Brazilian version of PAL - 525/60 rather than 625/50, different -## subcarrier -## -#sdtv_mode=0 - -## sdtv_aspect -## defines the aspect ratio for composite output -## -## Value Description -## ------------------------------------------------------------------------- -## 1 4:3 (Default) -## 2 14:9 -## 3 16:9 -## -sdtv_aspect=3 - -## sdtv_disable_colourburst -## Disables colour burst on composite output. The picture will be -## monochrome, but possibly sharper -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Colour burst is enabled (Default) -## 1 Colour burst is disabled -## -#sdtv_disable_colourburst=1 - -################################################################################ -## High Definition Video Settings -################################################################################ - -## hdmi_safe -## Use "safe mode" settings to try to boot with maximum hdmi compatibility. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Disabled (Default) -## 1 Enabled (this does: hdmi_force_hotplug=1, -## hdmi_ignore_edid=0xa5000080, -## config_hdmi_boost=4, hdmi_group=2, -## hdmi_mode=4, disable_overscan=0, -## overscan_left=24, overscan_right=24, -## overscan_top=24, overscan_bottom=24) -## -#hdmi_safe=1 - -## hdmi_force_hotplug -## Pretends HDMI hotplug signal is asserted so it appears a HDMI display -## is attached -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Disabled (Default) -## 1 Use HDMI mode even if no HDMI monitor is detected -## -#hdmi_force_hotplug=1 - -## hdmi_ignore_hotplug -## Pretends HDMI hotplug signal is not asserted so it appears a HDMI -## display is not attached -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Disabled (Default) -## 1 Use composite mode even if HDMI monitor is detected -## -#hdmi_ignore_hotplug=1 - -## hdmi_drive -## chooses between HDMI and DVI modes -## -## Value Description -## ------------------------------------------------------------------------- -## 1 Normal DVI mode (No sound) -## 2 Normal HDMI mode (Sound will be sent if supported and enabled) -## -#hdmi_drive=2 - -## hdmi_ignore_edid -## Enables the ignoring of EDID/display data -## -#hdmi_ignore_edid=0xa5000080 - -## hdmi_edid_file -## Read the EDID data from the edid.dat file instead of from the attached -## device -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Read EDID data from attached device (Default) -## 1 Read EDID data from edid.txt file -## -#hdmi_edid_file=1 - -## hdmi_ignore_edid_audio -## Pretends all audio formats are unsupported by display. This means ALSA -## will default to analogue. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Use EDID provided values (Default) -## 1 Pretend all audio formats are unsupported -## -#hdmi_ignore_edid_audio=1 - -## hdmi_force_edid_audio -## Pretends all audio formats are supported by display, allowing -## passthrough of DTS/AC3 even when not reported as supported. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Use EDID provided values (Default) -## 1 Pretend all audio formats are supported -## -#hdmi_force_edid_audio=1 - -## hdmi_force_edid_3d -## Pretends all CEA modes support 3D even when edid doesn't indicate -## support for them. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Use EDID provided values (Default) -## 1 Pretend 3D mode is supported -## -#hdmi_force_edid_3d=1 - -## avoid_edid_fuzzy_match -## Avoid fuzzy matching of modes described in edid. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Use fuzzy matching (Default) -## 1 Avoid fuzzy matching -## -#avoid_edid_fuzzy_match=1 - -## hdmi_pixel_encoding -## Force the pixel encoding mode. -## By default it will use the mode requested from edid so shouldn't -## need changing. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Use EDID provided values (Default) -## 1 RGB limited (16-235) -## 2 RGB full ( 0-255) -## 3 YCbCr limited (16-235) -## 4 YCbCr limited ( 0-255) -## -#hdmi_pixel_encoding=1 - -## hdmi_group -## Defines the HDMI type -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Use the preferred group reported by the edid (Default) -## 1 CEA -## 2 DMT -## -#hdmi_group=1 - -## hdmi_mode -## defines screen resolution in CEA or DMT format -## -## H means 16:9 variant (of a normally 4:3 mode). -## 2x means pixel doubled (i.e. higher clock rate, with each pixel repeated -## twice) -## 4x means pixel quadrupled (i.e. higher clock rate, with each pixel -## repeated four times) -## reduced blanking means fewer bytes are used for blanking within the data -## stream (i.e. lower clock rate, with fewer wasted bytes) -## -## Value hdmi_group=CEA hdmi_group=DMT -## ------------------------------------------------------------------------- -## 1 VGA 640x350 85Hz -## 2 480p 60Hz 640x400 85Hz -## 3 480p 60Hz H 720x400 85Hz -## 4 720p 60Hz 640x480 60Hz -## 5 1080i 60Hz 640x480 72Hz -## 6 480i 60Hz 640x480 75Hz -## 7 480i 60Hz H 640x480 85Hz -## 8 240p 60Hz 800x600 56Hz -## 9 240p 60Hz H 800x600 60Hz -## 10 480i 60Hz 4x 800x600 72Hz -## 11 480i 60Hz 4x H 800x600 75Hz -## 12 240p 60Hz 4x 800x600 85Hz -## 13 240p 60Hz 4x H 800x600 120Hz -## 14 480p 60Hz 2x 848x480 60Hz -## 15 480p 60Hz 2x H 1024x768 43Hz DO NOT USE -## 16 1080p 60Hz 1024x768 60Hz -## 17 576p 50Hz 1024x768 70Hz -## 18 576p 50Hz H 1024x768 75Hz -## 19 720p 50Hz 1024x768 85Hz -## 20 1080i 50Hz 1024x768 120Hz -## 21 576i 50Hz 1152x864 75Hz -## 22 576i 50Hz H 1280x768 reduced blanking -## 23 288p 50Hz 1280x768 60Hz -## 24 288p 50Hz H 1280x768 75Hz -## 25 576i 50Hz 4x 1280x768 85Hz -## 26 576i 50Hz 4x H 1280x768 120Hz reduced blanking -## 27 288p 50Hz 4x 1280x800 reduced blanking -## 28 288p 50Hz 4x H 1280x800 60Hz -## 29 576p 50Hz 2x 1280x800 75Hz -## 30 576p 50Hz 2x H 1280x800 85Hz -## 31 1080p 50Hz 1280x800 120Hz reduced blanking -## 32 1080p 24Hz 1280x960 60Hz -## 33 1080p 25Hz 1280x960 85Hz -## 34 1080p 30Hz 1280x960 120Hz reduced blanking -## 35 480p 60Hz 4x 1280x1024 60Hz -## 36 480p 60Hz 4x H 1280x1024 75Hz -## 37 576p 50Hz 4x 1280x1024 85Hz -## 38 576p 50Hz 4x H 1280x1024 120Hz reduced blanking -## 39 1080i 50Hz reduced blanking 1360x768 60Hz -## 40 1080i 100Hz 1360x768 120Hz reduced blanking -## 41 720p 100Hz 1400x1050 reduced blanking -## 42 576p 100Hz 1400x1050 60Hz -## 43 576p 100Hz H 1400x1050 75Hz -## 44 576i 100Hz 1400x1050 85Hz -## 45 576i 100Hz H 1400x1050 120Hz reduced blanking -## 46 1080i 120Hz 1440x900 reduced blanking -## 47 720p 120Hz 1440x900 60Hz -## 48 480p 120Hz 1440x900 75Hz -## 49 480p 120Hz H 1440x900 85Hz -## 50 480i 120Hz 1440x900 120Hz reduced blanking -## 51 480i 120Hz H 1600x1200 60Hz -## 52 576p 200Hz 1600x1200 65Hz -## 53 576p 200Hz H 1600x1200 70Hz -## 54 576i 200Hz 1600x1200 75Hz -## 55 576i 200Hz H 1600x1200 85Hz -## 56 480p 240Hz 1600x1200 120Hz reduced blanking -## 57 480p 240Hz H 1680x1050 reduced blanking -## 58 480i 240Hz 1680x1050 60Hz -## 59 480i 240Hz H 1680x1050 75Hz -## 60 1680x1050 85Hz -## 61 1680x1050 120Hz reduced blanking -## 62 1792x1344 60Hz -## 63 1792x1344 75Hz -## 64 1792x1344 120Hz reduced blanking -## 65 1856x1392 60Hz -## 66 1856x1392 75Hz -## 67 1856x1392 120Hz reduced blanking -## 68 1920x1200 reduced blanking -## 69 1920x1200 60Hz -## 70 1920x1200 75Hz -## 71 1920x1200 85Hz -## 72 1920x1200 120Hz reduced blanking -## 73 1920x1440 60Hz -## 74 1920x1440 75Hz -## 75 1920x1440 120Hz reduced blanking -## 76 2560x1600 reduced blanking -## 77 2560x1600 60Hz -## 78 2560x1600 75Hz -## 79 2560x1600 85Hz -## 80 2560x1600 120Hz reduced blanking -## 81 1366x768 60Hz -## 82 1080p 60Hz -## 83 1600x900 reduced blanking -## 84 2048x1152 reduced blanking -## 85 720p 60Hz -## 86 1366x768 reduced blanking -## -#hdmi_mode=1 - -## config_hdmi_boost -## configure the signal strength of the HDMI interface. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 (Default) -## 1 -## 2 -## 3 -## 4 Try if you have interference issues with HDMI -## 5 -## 6 -## 7 Maximum -## -#config_hdmi_boost=0 - -## hdmi_ignore_cec_init -## Doesn't sent initial active source message. Avoids bringing -## (CEC enabled) TV out of standby and channel switch when rebooting. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Normal behaviour (Default) -## 1 Doesn't sent initial active source message -## -#hdmi_ignore_cec_init=1 - -## hdmi_ignore_cec -## Pretends CEC is not supported at all by TV. -## No CEC functions will be supported. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Normal behaviour (Default) -## 1 Pretend CEC is not supported by TV -## -#hdmi_ignore_cec=1 - -################################################################################ -## Overscan Video Settings -################################################################################ - -## overscan_left -## Number of pixels to skip on left -## -#overscan_left=0 - -## overscan_right -## Number of pixels to skip on right -## -#overscan_right=0 - -## overscan_top -## Number of pixels to skip on top -## -#overscan_top=0 - -## overscan_bottom -## Number of pixels to skip on bottom -## -#overscan_bottom=0 - -## disable_overscan -## Set to 1 to disable overscan -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Overscan Enabled (Default) -## 1 Overscan Disabled -## -#disable_overscan=1 - -################################################################################ -## Framebuffer Video Settings -################################################################################ - -## framebuffer_width -## Console framebuffer width in pixels. Default is display width minus -## overscan. -## -#framebuffer_width=0 - -## framebuffer_height -## Console framebuffer height in pixels. Default is display height minus -## overscan. -## -#framebuffer_height=0 - -## framebuffer_depth -## Console framebuffer depth in bits per pixel. -## -## Value Description -## ------------------------------------------------------------------------- -## 8 Valid, but default RGB palette makes an unreadable screen -## 16 (Default) -## 24 Looks better but has corruption issues as of 2012/06/15 -## 32 Has no corruption issues but needs framebuffer_ignore_alpha=1 -## and shows the wrong colors as of 2012/06/15 -## -#framebuffer_depth=16 - -## framebuffer_ignore_alpha -## Set to 1 to disable alpha channel. Helps with 32bit. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Enable Alpha Channel (Default) -## 1 Disable Alpha Channel -## -#framebuffer_ignore_alpha=0 - -################################################################################ -## General Video Settings -################################################################################ - -## display_rotate -## Rotate the display clockwise or flip the display. -## The 90 and 270 degrees rotation options require additional memory on GPU, -## so won't work with the 16M GPU split. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 0 degrees (Default) -## 1 90 degrees -## 2 180 degrees -## 3 270 degrees -## 0x10000 Horizontal flip -## 0x20000 Vertical flip -## -#display_rotate=0 - -## dispmanx_offline -## Set to "1" to enable offline compositing -## -## Default 0 -## -#dispmanx_offline=0 - -################################################################################ -## Licensed Codecs -## -## Hardware decoding of additional codecs can be enabled by purchasing a -## license that is locked to the CPU serial number of your Raspberry Pi. -## -## Up to 8 licenses per CODEC can be specified as a comma seperated list. -## -################################################################################ - -## decode_MPG2 -## License key to allow hardware MPEG-2 decoding. -## -#decode_MPG2=0x12345678 - -## decode_WVC1 -## License key to allow hardware VC-1 decoding. -## -#decode_WVC1=0x12345678 - -################################################################################ -## Camera Settings -################################################################################ - -## start_x -## Set to "1" to enable the camera module. -## -## Enabling the camera requires gpu_mem option to be specified with a value -## of at least 128. -## -## Default 0 -## -#start_x=0 - -## disable_camera_led -## Turn off the red camera led when recording video or taking a still -## picture. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 LED enabled (Default) -## 1 LED disabled -## -#disable_camera_led=1 - -################################################################################ -## Test Settings -################################################################################ - -## test_mode -## Enable test sound/image during boot for manufacturing test. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Disable Test Mod (Default) -## 1 Enable Test Mode -## -#test_mode=0 - -################################################################################ -## Memory Settings -################################################################################ - -## disable_l2cache -## Disable arm access to GPU's L2 cache. Needs corresponding L2 disabled -## kernel. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Enable L2 Cache (Default) -## 1 Disable L2 cache -## -#disable_l2cache=0 - -## gpu_mem -## GPU memory allocation in MB for all board revisions. -## -## Default 64 -## -gpu_mem=128 - -## gpu_mem_256 -## GPU memory allocation in MB for 256MB board revision. -## This option overrides gpu_mem. -## -#gpu_mem_256=192 - -## gpu_mem_512 -## GPU memory allocation in MB for 512MB board revision. -## This option overrides gpu_mem. -## -#gpu_mem_512=448 - -## gpu_mem_1024 -## GPU memory allocation in MB for 1024MB board revision. -## This option overrides gpu_mem. -## -#gpu_mem_1024=944 - -## disable_pvt -## Disable adjusting the refresh rate of RAM every 500ms -## (measuring RAM temparature). -## -#disable_pvt=1 - -################################################################################ -## CMA - Dynamic Memory Split -## -## CMA enables dynamic management of the ARM and GPU memory split at runtime. -## -## The following options need to be in cmdline.txt for CMA to work: -## coherent_pool=6M smsc95xx.turbo_mode=N -## -################################################################################ - -## cma_lwm -## When GPU has less than cma_lwm (low water mark) memory available it -## will request some from ARM. -## -#cma_lwm=16 - -## cma_hwm -## When GPU has more than cma_hwm (high water mark) memory available it -## will release some to ARM. -## -#cma_hwm=32 - -################################################################################ -## Boot Option Settings -################################################################################ - -## disable_commandline_tags -## Stop start.elf from filling in ATAGS (memory from 0x100) before -## launching kernel -## -#disable_commandline_tags=0 - -## cmdline (string) -## Command line parameters. Can be used instead of cmdline.txt file -## -#cmdline="" - -## kernel (string) -## Alternative name to use when loading kernel. -## -#kernel="" - -## kernel_address -## Address to load kernel.img file at -## -#kernel_address=0x00000000 - -## kernel_old -## Support loading old kernels -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Disabled (Default) -## 1 Load kernel at address 0x00000000 -## -#kernel_old=1 - -## ramfsfile (string) -## ramfs file to load -## -#ramfsfile="" - -## ramfsaddr -## Address to load ramfs file at -## -#ramfsaddr=0x00000000 - -## initramfs (string address) -## ramfs file and address to load it at (it's like ramfsfile+ramfsaddr in -## one option). -## -## NOTE: this option uses different syntax than all other options - you -## should not use "=" character here. -## -#initramfs initramf.gz 0x00800000 - -## device_tree_address -## Address to load device_tree at -## -#device_tree_address=0x00000000 - -## init_uart_baud -## Initial uart baud rate. -## -## Default 115200 -## -#init_uart_baud=115200 - -## init_uart_clock -## Initial uart clock. -## -## Default 3000000 (3MHz) -## -#init_uart_clock=3000000 - -## init_emmc_clock -## Initial emmc clock, increasing this can speedup your SD-card. -## -## Default 100000000 (100mhz) -## -#init_emmc_clock=100000000 - -## boot_delay -## Wait for a given number of seconds in start.elf before loading -## kernel.img. -## -## delay = (1000 * boot_delay) + boot_delay_ms -## -## Default 1 -## -#boot_delay=0 - -## boot_delay_ms -## Wait for a given number of milliseconds in start.elf before loading -## kernel.img. -## -## delay = (1000 * boot_delay) + boot_delay_ms -## -## Default 0 -## -#boot_delay_ms=0 - -## avoid_safe_mode -## Adding a jumper between pins 5 & 6 of P1 enables a recovery Safe Mode. -## If pins 5 & 6 are used for connecting to external devices (e.g. GPIO), -## then this setting can be used to ensure Safe Mode is not triggered. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Respect Safe Mode input (Default) -## 1 Ignore Safe Mode input -## -#avoid_safe_mode=1 - -## disable_splash -## Avoids the rainbow splash screen on boot. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Splash screen enabled (Default) -## 1 Splash screen disabled -## -#disable_splash=1 - -################################################################################ -## Overclocking Settings -## -## ARM, SDRAM and GPU each have their own PLLs and can have unrelated -## frequencies. -## -## The GPU core, h264, v3d and isp share a PLL, so need to have related -## frequencies. -## pll_freq = floor(2400 / (2 * core_freq)) * (2 * core_freq) -## gpu_freq = pll_freq / [even number] -## -## The effective gpu_freq is automatically rounded to nearest even integer, so -## asking for core_freq = 500 and gpu_freq = 300 will result in divisor of -## 2000/300 = 6.666 => 6 and so 333.33MHz. -## -## -## Standard Profiles: -## arm_freq core_freq sdram_freq over_voltage -## ------------------------------------------------------------------------- -## None 700 250 400 0 -## Modest 800 300 400 0 -## Medium 900 333 450 2 -## High 950 450 450 6 -## Turbo 1000 500 500 6 -## -################################################################################ - -## force_turbo -## Control the kernel "ondemand" governor. It has no effect if no overclock -## settings are specified. -## May set warrany bit. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Enable dynamic clocks and voltage for the ARM core, GPU core and -## SDRAM (Default). -## Overclocking of h264_freq, v3d_freq and isp_freq is ignored. -## 1 Disable dynamic clocks and voltage for the ARM core, GPU core -## and SDRAM. -## Overclocking of h264_freq, v3d_freq and isp_freq is allowed. -## -#force_turbo=0 - -## initial_turbo -## Enables turbo mode from boot for the given value in seconds (up to 60) -## or until cpufreq sets a frequency. Can help with sdcard corruption if -## overclocked. -## -## Default 0 -## -#initial_turbo=0 - -## temp_limit -## Overheat protection. Sets clocks and voltages to default when the SoC -## reaches this Celsius value. -## Setting this higher than default voids warranty. -## -## Default 85 -## -#temp_limit=85 - -## arm_freq -## Frequency of ARM in MHz. -## -## Default 700. -## -arm_freq=900 - -## arm_freq_min -## Minimum frequency of ARM in MHz (used for dynamic clocking). -## -## Default 700. -## -#arm_freq_min=700 - -## gpu_freq -## Sets core_freq, h264_freq, isp_freq, v3d_freq together. -## -## Default 250. -## -#gpu_freq=250 - -## core_freq -## Frequency of GPU processor core in MHz. It has an impact on ARM -## performance since it drives L2 cache. -## -## Default 250. -## -#core_freq=250 - -## core_freq_min -## Minimum frequency of GPU processor core in MHz (used for dynamic -## clocking). It has an impact on ARM performance since it drives L2 cache. -## -## Default 250. -## -#core_freq_min=250 - -## h264_freq -## Frequency of hardware video block in MHz. -## -## Default 250. -## -#h264_freq=250 - -## isp_freq -## Frequency of image sensor pipeline block in MHz. -## -## Default 250. -## -#isp_freq=250 - -## v3d_freq -## Frequency of 3D block in MHz. -## -## Default 250. -## -#v3d_freq=250 - -## sdram_freq -## Frequency of SDRAM in MHz. -## -## Default 400. -## -#sdram_freq=400 - -## sdram_freq_min -## Minimum frequency of SDRAM in MHz (used for dynamic clocking). -## -## Default 400. -## -#sdram_freq_min=400 - -## avoid_pwm_pll -## Don't dedicate a pll to PWM audio. This will reduce analogue audio -## quality slightly. The spare PLL allows the core_freq to be set -## independently from the rest of the gpu allowing more control over -## overclocking. -## -## Value Description -## ------------------------------------------------------------------------- -## 0 Linked core_freq (Default) -## 1 Unlinked core_freq -## -#avoid_pwm_pll=1 - -################################################################################ -## Voltage Settings -################################################################################ - -## current_limit_override -## Disables SMPS current limit protection. Can help if you are currently -## hitting a reboot failure when overclocking too high. -## May set warrany bit. -## -#current_limit_override=0x5A000020 - -## over_voltage -## ARM/GPU core voltage adjust. -## May set warrany bit. -## -## Value Description -## ------------------------------------------------------------------------- -## -16 0.8 V -## -15 0.825 V -## -14 0.85 V -## -13 0.875 V -## -12 0.9 V -## -11 0.925 V -## -10 0.95 V -## -9 0.975 V -## -8 1.0 V -## -7 1.025 V -## -6 1.05 V -## -5 1.075 V -## -4 1.1 V -## -3 1.125 V -## -2 1.15 V -## -1 1.175 V -## 0 1.2 V (Default) -## 1 1.225 V -## 2 1.25 V -## 3 1.275 V -## 4 1.3 V -## 5 1.325 V -## 6 1.35 V -## 7 1.375 V (requires force_turbo=1 or current_limit_override) -## 8 1.4 V (requires force_turbo=1 or current_limit_override) -## -#over_voltage=0 - -## over_voltage_min -## Minimum ARM/GPU core voltage adjust (used for dynamic clocking). -## -## Value Description -## ------------------------------------------------------------------------- -## -16 0.8 V -## -15 0.825 V -## -14 0.85 V -## -13 0.875 V -## -12 0.9 V -## -11 0.925 V -## -10 0.95 V -## -9 0.975 V -## -8 1.0 V -## -7 1.025 V -## -6 1.05 V -## -5 1.075 V -## -4 1.1 V -## -3 1.125 V -## -2 1.15 V -## -1 1.175 V -## 0 1.2 V (Default) -## 1 1.225 V -## 2 1.25 V -## 3 1.275 V -## 4 1.3 V -## 5 1.325 V -## 6 1.35 V -## 7 1.375 V (requires force_turbo=1) -## 8 1.4 V (requires force_turbo=1) -## -#over_voltage_min=0 - -## over_voltage_sdram -## Sets over_voltage_sdram_c, over_voltage_sdram_i, over_voltage_sdram_p -## together -## -## Value Description -## ------------------------------------------------------------------------- -## -16 0.8 V -## -15 0.825 V -## -14 0.85 V -## -13 0.875 V -## -12 0.9 V -## -11 0.925 V -## -10 0.95 V -## -9 0.975 V -## -8 1.0 V -## -7 1.025 V -## -6 1.05 V -## -5 1.075 V -## -4 1.1 V -## -3 1.125 V -## -2 1.15 V -## -1 1.175 V -## 0 1.2 V (Default) -## 1 1.225 V -## 2 1.25 V -## 3 1.275 V -## 4 1.3 V -## 5 1.325 V -## 6 1.35 V -## 7 1.375 V -## 8 1.4 V -## -#over_voltage_sdram=0 - -## over_voltage_sdram_c -## SDRAM controller voltage adjust. -## -## Value Description -## ------------------------------------------------------------------------- -## -16 0.8 V -## -15 0.825 V -## -14 0.85 V -## -13 0.875 V -## -12 0.9 V -## -11 0.925 V -## -10 0.95 V -## -9 0.975 V -## -8 1.0 V -## -7 1.025 V -## -6 1.05 V -## -5 1.075 V -## -4 1.1 V -## -3 1.125 V -## -2 1.15 V -## -1 1.175 V -## 0 1.2 V (Default) -## 1 1.225 V -## 2 1.25 V -## 3 1.275 V -## 4 1.3 V -## 5 1.325 V -## 6 1.35 V -## 7 1.375 V -## 8 1.4 V -## -#over_voltage_sdram_c=0 - -## over_voltage_sdram_i -## SDRAM I/O voltage adjust. -## -## Value Description -## ------------------------------------------------------------------------- -## -16 0.8 V -## -15 0.825 V -## -14 0.85 V -## -13 0.875 V -## -12 0.9 V -## -11 0.925 V -## -10 0.95 V -## -9 0.975 V -## -8 1.0 V -## -7 1.025 V -## -6 1.05 V -## -5 1.075 V -## -4 1.1 V -## -3 1.125 V -## -2 1.15 V -## -1 1.175 V -## 0 1.2 V (Default) -## 1 1.225 V -## 2 1.25 V -## 3 1.275 V -## 4 1.3 V -## 5 1.325 V -## 6 1.35 V -## 7 1.375 V -## 8 1.4 V -## -#over_voltage_sdram_i=0 - -## over_voltage_sdram_p -## SDRAM phy voltage adjust. -## -## Value Description -## ------------------------------------------------------------------------- -## -16 0.8 V -## -15 0.825 V -## -14 0.85 V -## -13 0.875 V -## -12 0.9 V -## -11 0.925 V -## -10 0.95 V -## -9 0.975 V -## -8 1.0 V -## -7 1.025 V -## -6 1.05 V -## -5 1.075 V -## -4 1.1 V -## -3 1.125 V -## -2 1.15 V -## -1 1.175 V -## 0 1.2 V (Default) -## 1 1.225 V -## 2 1.25 V -## 3 1.275 V -## 4 1.3 V -## 5 1.325 V -## 6 1.35 V -## 7 1.375 V -## 8 1.4 V -## -#over_voltage_sdram_p=0 - -################################################################################ -## USB Power -################################################################################ - -## max_usb_current -## When set to 1, change the output current limit (for all 4 USB -## ports combined) from 600mA to double that, 1200mA. -## -## This option is not available for Model A/B boards. -## -## Default 0. -## -#max_usb_current=0 - -################################################################################ -## Base Device Tree Parameters -################################################################################ - -## audio -## Enable the onboard ALSA audio -## -## Default off. -## -dtparam=audio=on - -## i2c_arm -## Enable the ARM's i2c interface -## -## Default off. -## -#dtparam=i2c_arm=off - -## i2c_vc -## Enable the i2c interface -## -## Usually reserved for the VideoCore processor -## -## Default off. -## -#dtparam=i2c_vc=off - -## i2c_arm_baudrate -## Set the baudrate of the ARM's i2c interface -## -## Default 100000. -## -#dtparam=i2c_arm_baudrate=100000 - -## i2c_vc_baudrate -## Set the baudrate of the VideoCore i2c interface -## -## Default 100000. -## -#dtparam=i2c_vc_baudrate=100000 - -## i2s -## Set to "on" to enable the i2s interface -## -## Default off. -## -#dtparam=i2s=off - -## spi -## Set to "on" to enable the spi interfaces -## -## Default off. -## -#dtparam=spi=off - -## random -## Set to "on" to enable the hardware random -## -## Default off. -## -#dtparam=random=off - -## uart0 -## Set to "off" to disable uart0 -## -## Default on. -## -#dtparam=uart0=on - -## watchdog -## Set to "on" to enable the hardware watchdog -## -## Default off. -## -#dtparam=watchdog=off - -## act_led_trigger -## Choose which activity the LED tracks. -## -## Use "heartbeat" for a nice load indicator. -## -## Default mmc. -## -#dtparam=act_led_trigger=mmc - -## act_led_activelow -## Set to "on" to invert the sense of the LED -## -## Default off. -## -#dtparam=act_led_activelow=off - -## act_led_gpio -## Set which GPIO to use for the activity LED -## -## In case you want to connect it to an external device -## -## Default 16 on a non-Plus board, 47 on a Plus or Pi 2. -## -#dtparam=act_led_gpio=47 - -## pwr_led_trigger -## Choose which activity the LED tracks. -## -## Use "heartbeat" for a nice load indicator. -## -## Not available on Model A/B boards. -## -## Default mmc. -## -#dtparam=pwr_led_trigger=mmc - -## pwr_led_activelow -## Set to "on" to invert the sense of the LED -## -## Not available on Model A/B boards. -## -## Default off. -## -#dtparam=pwr_led_activelow=off - -## pwr_led_gpio -## Set which GPIO to use for the PWR LED -## -## In case you want to connect it to an external device -## -## Not available on Model A/B boards. -## -## Default 35. -## -#dtparam=pwr_led_gpio=35 diff --git a/rpi3+/10-vchiq-permissions.rules b/rpi3+/10-vchiq-permissions.rules new file mode 100644 index 0000000..bacea0e --- /dev/null +++ b/rpi3+/10-vchiq-permissions.rules @@ -0,0 +1 @@ +SUBSYSTEM=="vchiq",GROUP="video",MODE="0660" diff --git a/rpi3+/mageia4arm.cfg.original b/rpi3+/mageia4arm.cfg.original new file mode 100644 index 0000000..e1b78d9 --- /dev/null +++ b/rpi3+/mageia4arm.cfg.original @@ -0,0 +1,56 @@ + +# Copyright (C) 2017-2018 Daniel Tartavel-jeannot +# +# This program is free software; you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation; either version 2 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see . + + +MAGEIA_VERSION="7" +ARM_VERSION="armv7hl" + +#target plateform (xu3-4 or rpi) +TARGET="rpi" + +# URL of the Mageia mirror used to install ( see mirrors.mageia.org ) +MIRROR="http://ftp.free.fr/mirrors/mageia.org/distrib/$MAGEIA_VERSION/$ARM_VERSION" +# image will be created here +INSTALL_PATH="" + +# Build directory will be created here +BUILD_PATH="$INSTALL_PATH/build" + +#name of the image +IMAGE="Mageia-${MAGEIA_VERSION}-$TARGET.img" + +#Mount point of image's partitions +#no need to be changed +BOOT="/mnt/boot" +ROOT="/mnt/root" + +#Default user +ID_USER="pi" +PASSWORD="raspberry" + +#root password +ROOT_PWD="piroot" + +#Hostname +HOSTNAME="$TARGET.$ID_USER" + +#Filesystem of boot partitions (default ext4 raspberry pi need vfat) +#DO NOT CHANGE THIS +BOOTFS="vfat" + +#Path where the raspberry pi firmware is/will be downloaded +FIRMWARE_PATH="$INSTALL_PATH" +FIRMWARE_DIR="firmware-stable" diff --git a/rpi3+/modprobe.conf b/rpi3+/modprobe.conf new file mode 100644 index 0000000..7725dae --- /dev/null +++ b/rpi3+/modprobe.conf @@ -0,0 +1,3 @@ +alias wlan0 brcmfmac +alias eth0 smsc95xx +alias usb0 rndis_host diff --git a/rpi3+/second_stage_install.sh b/rpi3+/second_stage_install.sh new file mode 100644 index 0000000..1848789 --- /dev/null +++ b/rpi3+/second_stage_install.sh @@ -0,0 +1,41 @@ +#!/bin/bash + +# Copyright (C) 2017-2018 Daniel Tartavel-jeannot +# + +# This program is free software; you can redistribute it and/or modify +# it under the terms of the GNU General Public License as published by +# the Free Software Foundation; either version 2 of the License, or +# (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see . + +/usr/bin/chown :shadow /etc/shadow /etc/gshadow /etc/login.defs /etc/pam.d/chage-chfn-chsh /etc/pam.d/chpasswd-newusers /etc/pam.d/system-auth /etc/pam.d/user-group-mod /bin/passwd /bin/chage + +/usr/bin/chown :systemd-journal -R /var/log/journal + +#Install all packages you need +# No verifying rpm due to a bug in packages, some are not signed + +/usr/sbin/urpmi --auto --no-verify-rpm basesystem chrony rng-tools man openssh-server rfkill wireless-tools bluez wpa_supplicant make binutils dracut u-boot rsync kernel-desktop-latest mlocate drakx-kbd-mouse-x11 + + +/usr/bin/chown :chrony -R /etc/chrony.keys /var/log/chrony +/usr/bin/chown :daemon /etc/wpa_supplicant.conf +/usr/bin/chown :tty /bin/write /bin/wall +/usr/bin/chown :lock /sbin/lockdev +/usr/bin/chown :bin /sbin/traceroute +/usr/bin/chown polkitd /etc/polkit-1/rules.d + +KV=`basename /boot/vmlinuz-*` +KV=${KV#vmlinuz-} +dracut --kver $KV +rm -f $0 +cp /boot/vmlinuz-* /boot/vmlinuz +cp /boot/initrd-* /boot/initrd diff --git a/tools/install_graphical.sh~ b/tools/install_graphical.sh~ deleted file mode 100755 index adba427..0000000 --- a/tools/install_graphical.sh~ +++ /dev/null @@ -1,27 +0,0 @@ -#!/bin/bash - -# Copyright (C) 2017-2018 Daniel Tartavel-jeannot -# - -# This program is free software; you can redistribute it and/or modify -# it under the terms of the GNU General Public License as published by -# the Free Software Foundation; either version 2 of the License, or -# (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program. If not, see . - -if [ "$1" = "" ];then - echo "syntax install_graphical.sh [xfce | lxde | lxqt | plasma | gnome] ( see task-* for all )" -else - PATH="$(/bin/dirname "$(readlink -f "$0")")" - echo "Path="$PATH - . $PATH/install_video_driver.sh - . $PATH/install_gstreamer.sh - /usr/sbin/urpmi --auto --no-verify-rpm task-$1 -fi diff --git a/tools/install_video_driver.sh~ b/tools/install_video_driver.sh~ deleted file mode 100755 index a0ba320..0000000 --- a/tools/install_video_driver.sh~ +++ /dev/null @@ -1,26 +0,0 @@ -#!/bin/bash - -# Copyright (C) 2017-2018 Daniel Tartavel-jeannot -# - -# This program is free software; you can redistribute it and/or modify -# it under the terms of the GNU General Public License as published by -# the Free Software Foundation; either version 2 of the License, or -# (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program. If not, see . - - -/usr/sbin/urpmi --auto --no-verify-rpm x11-driver-video-fbdev xinit xclock - -echo "#!/bin/sh - -# patch for display manager service which do not start automatically -systemctl start display-manager.service &" >/etc/rc.d/rc.local -/usr/bin/chmod a+x /etc/rc.d/rc.local diff --git a/tools/install_xfce.sh~ b/tools/install_xfce.sh~ deleted file mode 100755 index 24118d0..0000000 --- a/tools/install_xfce.sh~ +++ /dev/null @@ -1,23 +0,0 @@ -#!/bin/bash - -# Copyright (C) 2017-2018 Daniel Tartavel-jeannot -# - -# This program is free software; you can redistribute it and/or modify -# it under the terms of the GNU General Public License as published by -# the Free Software Foundation; either version 2 of the License, or -# (at your option) any later version. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program. If not, see . - -PATH="$(/bin/dirname "$(readlink -f "$0")")" -echo "Path="$PATH -. $PATH/install_video_driver.sh -. $PATH/install_gstreamer.sh -/usr/sbin/urpmi --auto --no-verify-rpm task-xfce